System Ships in Approximately 5 - 20 Business Days After Funds Clear. (NOTE: Power Center Subject to Seasonal Increases 10 to 30 Business Days) ● Line Drawing send via Email [PDF] 5 - 20 business days after funds clear.
[See Related Items Below] Solar panel roof or ground racks & batteries are site specific options that are not included with the base package. Scroll down related items. ⇩
RECOMMENDATION - Keep the number of parallel strings of batteries to three or fewer. More than three strings of batteries will shorten your battery life due to uneven charging. That means use higher AH 6VDC or 2VDC batteries for fewer strings. Batteries in Series = Voltage is Additive; Batteries in Parallel = Ah is Additive.
Solar Production = 3,600 Watts Per Day ● Assumptions: STC 300 Watt Panel Rating [Factory Rating] @ 4.0 Sun Hours (Dec). Sun Hours should reflect the average value of total solar energy received in peak-sun-hours per day on an optimally-tilted surface during the month with the lowest solar radiation (not the yearly average). This is the best number to use in off-grid system design where the electrical demand is continuous or is not expected to vary seasonally and the system must be designed to operate year-round.
Technical Specifications: FP1 VFXR3648A-01 Power Center ● 48 VDC Battery Based Inverter. 120 VAC Output, Continuous Inverter AC Output Current 30 AAC ● Charge Controller FM80 Charge Controller FM80 Recommended Solar Maximum Array STC Nameplate: 48VDC system = 5000W; ● 120 VAC Generator Compatible
IMPORTANT: Amps AC Output; Define Your Load Amp Requirements: OutBack Power 3.6kW FLEXpower One™ FP1 VFXR3648A-01 Pre-wired Power Center continuous AC output current is limited to 30 AAC. The concern here is that the combination of your normal loads (Not Surge Loads) might exceed the inverters output current rating (Amps Out). It is critical in the design selection that you make sure the continuous AC load combination of your power requirements at the site is at or below the 30 AAC output limit of a OutBack Power 3.6kW FLEXpower One™ power center.
The FLEXpower ONE is ideal for smaller residential applications including cabins, vacation homes, farm buildings, remote communications sites and back-up power systems, with all necessary components integrated into a compact hang-on-the-wall system with a minimal footprint.
● Factory tested, pre-wired and pre-configured systems
● Off-grid and grid-tied functionality in one flexible system
Programmable for seven different modes including GridZero, which blends utility power and stored renewable energy, minimizing grid dependence; also Support Mode for seamless generator integration.
The Grid Tied mode allows the FP1 VFXR3648A-01 inverter to become grid-interactive. This means that in addition to using power from the utility grid for charging and loads, the inverter can also convert excess battery power and will export excess power to the utility grid. Excess battery power usually comes from renewable energy sources, such as solar arrays, hydroelectric turbines, and wind turbines.
Backup functionality requires a seperate critical load panel.
CA Rule 21 currently governs CA & HI Rule 14H utility interconnection for all net energy metering for all projects permitted and approved for interconnection. The change was designed to create a standard for inverters more capable of dealing with a volatile utility grid. Why is this needed? Utility companies are facing higher penetration rates of solar and in some cases are saturated and needed an additional low/high frequency ride-through. By using so called smart inverters the functionality keeps grid voltage from oscillating or acts like a shock absorber intended result is automatic stabilization of utiltiy grid voltage.
Line drawing questions or just stuck? No worries we have your back and will be here to help whenever you have questions about your purchased Kit. For orders larger than $2,000.00 a Technical Sales Team Group Captain will be assigned your account. Your Technical Advisors job is to coordinate all parts and pieces of your order and to work with you throughout the process. This support helps because we will be providing you with a single contact point to call with your questions. Your technical support contact does not replace the maufactures warranty technical support. DIY means you accept the responsiblity of reading and following the line diagram and other installation documents prior to tackling the installation.
NOTE: For detail support after installation customer must be willing or have the ability to connect to the system monitoring via web interface with OutBack OPTICS RE. The monitoring platform software is free but requires a WiFi connnection to the Mate3s Controller via RS485 .
Blue Pacific Solar® SolarEdge Kit is featured with Mission panels. Mission Solar Energy, proudly assembled in the USA, is headquartered in San Antonio, TX with module facilities onsite. Mission Solar hardworking team calls Texas home and is devoted to producing high quality solar products. Our supply chain includes local and domestic vendors. 25 Year Warranty, UL Listed.
The federal solar tax credit, also known as the investment tax credit (ITC), allows a taxpayer to claim a credit of 26 percent for a qualified system located in the USA and that is owned and used as a residence by the taxpayer.