Grid-Tie Inverters

grid interactive

web solarStore

 

 

  • Blue Pacific Solar Products, Inc. BBB Business Review

 

Enphase Energy M250-60-2LL-S22 Grid-Tie Microinverter

M250
     
  • M250-60-2LL-S22 Microinverter
  • The M250 microinverter is compatible with most 60-cell PV modules (up to 300 W) and works with 240 VAC single-phase services. The maximum number of M250 microinverters in an AC branch circuit is 16 for 240 VAC single-phase systems. Each AC branch circuit must be protected with a 20 A circuit breaker. The M250 has automatic voltage sensing, but the Engage trunk cable used to complete the circuit is specific to the output voltage required. Be sure to verify that the voltage and current specifications of your PV module are within the input range of the M250 microinverter. A list of electrically-compatible PV modules can be found on the Enphase.com website. To ensure mechanical compatibility, be sure to order the microinverter with the correct connector type for the PV module that you are using.
  • Only: Discontinued by Enphase Buy Now
  • Product Details:
  • Specifications:
  • Videos:
  • Documents:

Enphase M250 Microinverter

Model Part Number MAX AC
Output
DC Panel Voltage MPPT Range CEC* Efficiency Max AC Current Weight
M250-60-2LL-S22 3210194 240 Watts < 48 VDC 27 to 39 VDC 96.5% 1.15 Amp 4.4 lb

grid-interactive definition*California Energy Commission Independent Test Performance

necCAUTION: Enphase M250™ Microinverters can be paired only with a 60-cell solar panel. Modules with STC watt rating > 265 watts are often 72 cell panels. Panels paired with the M250 must use "PV Wire" or "PV Cable” to be compliant with NEC 690.35(D) for Ungrounded PV Power Systems.

A microinverter converts the DC output from a single solar panel into grid-compliant AC power and is meant to be located near the panel. The Enphase Microinverter System simplifies design and installation by alleviating string-sizing constraints, and it optimizes the energy harvest of each module through independent maximum power point tracking (MPPT). An Enphase System consists of microinverters, Engage trunk cables, the Envoy Communications Gateway, and the web-based Enlighten monitoring and analysis service.

Through individualized MPPT, Enphase microinverters help mitigate the effects of shading, dust, debris, module mismatch, and thermal differences. With module-level monitoring, performance issues can be traced to individual modules to expedite troubleshooting. Each solar panel is connected directly to its own microinverter, typically mounted on the racking underneath. The microinverters’ AC wire harnesses are connected to form an AC branch circuit that leads to the AC utility distribution center. System safety is enhanced since all of the output wiring from the PV array is AC and no high-voltage DC is present once the AC power is shut down, reducing risk to maintenance personnel or firefighters.

FEATURES:

  • Module-level Monitoring - Requires Envoy ENV
  • Cable Selectable 240 VAC Output - Requires Engage Trunk Cable
  • Operate at Full Power in Ambient Temperatures from -40°C (-40°F) to 65°C (149°F)
  • NEMA6 Sealed Enclosures
  • Listed to UL 1741 for U.S. and Canada
  • Compliant with: IEEE 1547 FCC Part 15 Class B CAN/CSA-C22.2 NO. 0-91, .4-04, and 107.1-01
  • Backed by a Twenty Five Year Limited Warranty

 

Fronius

What's On The Truck

  • Enphase, M250 Microinverter, 250W, 240/208VAC, 60Hz, 16-45VDC for 60 cell modules, H4 PV in, 16" Engage Cable out, 25 Yr Warranty, M250-60-2LL-S22

controller shipEnphase Energy Microinverters ship in 2 - 3 business days after funds clear.

 

Optional Accessories Part # Price  
Enphase, Envoy Communications Gateway Monitor, includes Wireless USB adapter (WiFi 802.11b/g/n), with Lifetime MyEnlighten System level monitoring, ENV-120-02 Menvoy  3600297enphase Discontinued by Enphase
Qty
Enphase, Engage Portrait AC Trunk Cable, 1-Ph (4-Wire) for M250 and M250, Qty 1 Per Microinverter, Continuous length in Portrait (40"), ET10-240-BULKenvoy  3600217enphase
Qty
Enphase, Engage Landscape AC Trunk Cable, 1-Ph (4-Wire) for M250 and M250, Qty 1 Per Microinverter, Continuous length in Landscape (67"), ET17-240-BULKenvoy  3600216enphase
Qty
Enphase, Install Kit for M250 and M250 (4 Terminators, 1 Disconnect Tool, 5 Water tight caps), ET-INSTLenvoy  3600206enphase
Qty
Enphase, Mounting Bracket for Dual Gang AC JBox, Qty. 1, EMBK-50-001  3600165enphase
Qty
Enphase, Engage Coupler, Watertight Cable Splice for M250 and M250, Qty. 1, ET-SPLK-05envoy  3600204enphase
Qty
Enphase, Branch Terminator for M250 and M250, ET-TERM-10  3600203enphase
Qty
Enphase, Accessory, Water tight cap for M250 and M250, Qty. 1, ET-SEAL-10  3600205enphase
Qty
Enphase, Accessory, Cable Disconnect Tool, M250 and M250, ET-DISC-05 (Minimum Qty 3)  3700055enphase
Qty
roof mount panels 
M250

 

 

 

 

Enphase M250 Microinverter System Grid Tie; Grid Interactive Power

Enphase Energy M250-60-2LL-S22 Grid-Tied Inverter; Simple Overview of the Installation Process:

  • Step 1 – Measure AC at the Electrical Utility Connection (See Enphase installation instruction sheet under "Documents" tab above)
  • Step 2 – Install the AC Branch Circuit Junction Box (Not included)
  • Step 3 – Position the Enphase Engage Cable
  • Step 4 – Attach the MicroInverter to the Solar Racking
  • Step 5 – Dress the Enphase Engage Cable
  • Step 6 – Terminate the Unused End of the Engage Cable
  • Step 7 – Connect the Engage Cable to AC Junction Box(s)
  • Step 8 – Complete the Enphase M250 Installation Map
  • Step 9 – Connect the Solar Panels
  • Step 10 – Build the Virtual Array
necresidential

NOTE IMPORTANT INSTALLATION Enphase Energy M250-60-2LL-S22 : It is the responsibility of the purchaser to ensure that all products are installed and operated in accordance with local and national building codes as specific by the NEC (National Electric Code), UBC (Uniform Building Code) or IBC (International Building Code) and local utility company policy. These codes may vary from city to city and county to county. All Grid-tied solar installations should be permitted and inspected, where required, by the local inspection authority in the same manner as other equivalent electrical systems. It is always a good idea to contract with a local licensed electrician to at least do the final electrical connection of your Enphase Energy M250-60-2LL-S22 system from the AC disconnect to your home utility breaker box. Some local permitting authorities require that a licensed electrician do all the wiring from the rack to the utility interconnect.

Additional Safety Instructions; Perform all electrical installations in accordance with all applicable local electrical codes and the National Electrical Code (NEC), ANSI/NFPA 70. Be aware that only qualified personnel should install or replace Enphase MicroInverter. Do not attempt to repair the Enphase MicroInverter as it contains no user-serviceable parts. If it fails, please contact Enphase customer service to obtain an RMA (return merchandise authorization) number and start the replacement process. Tampering with or opening the Enphase MicroInverter will void the warranty. Before installing or using the Enphase Energy M250-60-2LL-S22, please read all instructions and cautionary markings in the technical description. Connect the Microinverter to the utility grid only after receiving prior approval from the electrical utility company. Be aware that the body of the microinverter is the heat sink. Under normal operating conditions, the temperature is 15°C above ambient, but under extreme conditions the microinverter can reach a temperature of 80°C. To reduce risk of burns, use caution when working with microinverter. Do NOT disconnect the solar panel from the Enphase Energy M250-60-2LL-S22 without first removing AC power.